EMT Practice Test

1. Question Content...

Previous Submit Next
Was this helpful? Upvote!
Question List

Question1: A customer's data center has cool air distributed by means of the plenum under the raised floor.
What should the integrator recommend to the customer to enable more efficient cooling of the rack- mounted HPE ProLiant Gen9 servers?

Question2: An integrator is setting up arrays on an HPE Smart Array controller for a customer with eight drives. The controller supports several RAID options. The RAID volume must be able to tolerate any two drive failures without downtime.
Which solution should the integrator choose to meet the criteria?

Question3: DRAG DROP
Click and drag each HPE integrated management tool to its matching function.
Select and Place:

Question4: A customer needs to use a Smart Array controller to meet the following requirements:
Provides enterprise-class storage performance

Has all RAID capabilities

Provides the flexibility of having open PCIe slots for future expansion in ProLiant 300 Gen9 series

servers.
Which Smart Array controller meets the customer's needs?

Question5: Refer to the exhibit.
A server integrator is configuring the power management on HPE Onboard Administrator. The customer finds power related information confusing and the integrator needs to explain why the power allocation shown is greater than the present power reading.
How should the integrator explain the difference?

Enclosure Power (AC Input Power): The Present Power reading is the actual measurement of AC input power drawn by the enclosure and all devices.
Note: The AC input Wattage draw is calculated for the enclosure (including all of its devices) based on the known AC Wattage values obtained from the enclosure's power supplies. The Power Limit value can change depending on the current Power Mode (power redundancy setting) and the number and location of power supplies.

Question6: While creating a baseline for the Gen9 blades in a new HPE c7000 BladeSystem Enclosure in an active/ active configuration, an integrator determines that one blade has a NIC teaming setting of fail over.
What will be the outcome of this setting in an active/active high availability configuration?

Question7: HOTSPOT
Click one of the components in the Insight Display that is powered off.
Hot Area:

Question8: Through HPE OneView, an integrator determines that n HPE ProLiant Gen9 Server is experiencing errors during its boot process. As the next troubleshooting step, the integrator needs to investigate the issues in more detail without going to the server's physical location.
How can the integrator achieve the goal?

Question9: An integrator needs to ensure that an HPE ProLiant ML150 Gen9 Server consistently has the most current updates for firmware and drives.
Which tool's current version should the integrator use to accomplish this?

Question10: What is a benefit of advanced memory protection on an HPE ProLiant BL460c Gen9 Server Blade?

Question11: An integrator needs to connect a series of HPE ProLiant Gen9 BladeSystem servers to the network so that they can be managed remotely regardless of the operating system.
What should the integrator connect to the network to achieve this?

Question12: Which utility replaced the Array Configuration Utility?

Question13: A customer needs to monitor device health, obtain warranty status, and track support cases for its HPE ProLiant Gen8 and 9 servers as well as its HPE Smart Storage products.
Which tool meets the customer's needs?

Question14: Under which circumstance will a server integrator need to access the HPE Unified Extensible Firmware Interface (UEFI)?

Question15: An integrator using HPE Insight Diagnostics Online Edition can run performance diagnostics on which components? (Select two.)

Question16: A customer has added a storage blade to its HPE c7000 BladeSystem Enclosure, however the external storage is not visible from the adjacent HPE ProLiant BL460c Gen9 server blade.
What should the integrator do in order for the ProLiant BL40c Gen9 server blade to recognize the adjacent storage?

Question17: What is a benefit of using 20Gb FlexFabric converged network adapter (CAN) for the BladeSystems?

Question18: A server integrator needs to ensure that IT staff can access all HPE ProLiant Gen 9 servers running MS Windows 2012 even when the operating system is running.
How can the integrator accomplish this?

Question19: A customer's design includes a 40GB uplink to their data center network.
Which ports on the HPE Virtual Connect FlexFabric-20/40 F8 Module should the integrator use to connect the uplinks?

Question20: An integrator with 25 HPE ProLiant servers that run MS Windows Server 2012 needs to ensure that the latest drives and firmware are installed.
Which tool should the integrator use to accomplish this?

Question21: An integrator needs to view the health status on HPE ProLiant servers. The integrator also needs to be able to view warranty and support information if a hardware problem is identified.
Which management tool enables the integrator to perform both of these tasks?

Question22: An integrator uses HPE Insight Control server provisioning (ICsp) to deploy drivers to the HPE ProLiant servers running Windows and Linux. A new version of the Service Pack for ProLiant (SPP) is available.
Which ICsp component should the integrator update in order to make this new SPP available for deployment?

Question23: An integrator installs an HPE ProLiant BL 460c Gen9 server into an HPE c7000 BladeSystem Enclosure that has HPE Virtual Connect Flex-10 Ethernet modules in interconnect bays 1 and 2, and HPE Virtual Connect 8Gb 24-Port Fibre Channel modules in interconnect bays 3-6. The blade is configured with two HPE LPe1605 16Gb Fibre Channel HBAs in mezzanine slots 1 and 2, 32 Gb memory, and a single E-2600 v3 processor.
Next, the integrator installs ESXi 5.5 update 2 on the server. However, only one HBA is recognized in the operating system. As a troubleshooting step, the integrator replaces the HBAs in the problem server with known working HBAs from another server. However, ESXi still recognizes only one HBA.
Which step should the integrator take to allow the server to recognize both HBAs?

Question24: Refer to the exhibit.

A customer is using HPE OneView and HPE c7000 BladeSystem Enclosure with BL460c Gen9 server blades. The integrator changed a server blade in a bay, but profile settings were not applied.
Which change should the integrator make in the server profile shown to avoid this situation in the future?

Question25: An integrator needs to run HPE Insight Diagnostics to run some diagnostics on the processor and memory of one of the MS Windows 2012 Servers.
Which tool will accomplish this?

Question26: A customer needs a solution to prevent their five HPE ProLiant DL380 Gen9 servers from powering off due to a 10-second utility power loss.
Which power support solution should the integrator recommend to the customer?

Question27: Refer to exhibit.

A customer environment has a variety of HPE ProLiant Gen9 servers. The customer needs to add HPE Secure Encryption for their environment using the HPE Smart HBA H240ar Controller as shown.
In which Gen9 server in the customer's environment is this adapter supported?

Question28: Which pre boot environment allows an integrator to update firmware with a fwupdate command?

Question29: An HPE ProLiant Gen9 server running Server 2012 located at a remote site is not functioning property and cannot be accessed by any Remote Desktop applications. An integrator at the data center needs to access this remote server and find out what is causing the issue.
Which tool on the remote server can the integrator use to accomplish this?

Question30: Which technology provides monitoring of power consumption at the core, load segment, stick, and outlet level with precision and accuracy in a core-and-stick architecture?

Question31: A customer is planning where to locate their servers in the data server and how to manage and monitor power consumption.
They have purchased HPE iPDU units for the cabinets where HPE ProLiant Gen9 servers will be installed.
Which guideline must the integrator follow when installing the new iPDUs?

Question32: A customer needs to mount a group virtual media and install the operating system on 25 HPE ProLiant DL360 Gen9 servers using iLO4.
What should the integrator do? (Select two.)

Question33: An integrator needs to install three HPE ProLiant BL460 Gen9 servers in an HPE c7000 BladeSystem Enclosure that has BL460 Gen8 and BL460 G7 servers installed using Virtual Connect.
Which steps are mandatory for the integrator to take before installing the new Gen9 blades in over to prevent compatibility problems? (Select two.)